Select Set Boot Sequence: Configure as 1st Boot Device.

选择设置引导顺序：配置为第一引导设备。

First you must set up the boot sequence in the BIOS.

首先你必须在BIOS中设置启动顺序。

At the end of the kernel boot sequence, the init process starts.

在内核引导序列的结尾，会启动init进程。

The boot sequence for Mepis is a bit different than that of Knoppix.

Mepis的引导顺序与Knoppix稍有不同。

You will change the boot sequence for the new JS20 blade server from this screen.

您将通过这一屏幕改变新的JS20刀片服务器的引导次序。

In particular, it expects user interaction for its boot sequence and configuration.

特别地，它希望在确定其引导顺序和配置时能与用户进行交互。

In other words, the boot sequence won't start until the correct password is provided.

换句话说，除非给出正确密码，否则引导系列过程不会启动。

During the boot sequence of the AMI instance, you are asked to set the password for this user.

在ami实例启动期间，将要求您为该用户设置密码。

This error is returned if GRUB is told to execute the boot sequence without having a kernel to start.

看了翻译内核必须在开始引导系统之前被载入GRUB开始执行引导系统时发现没有内核。

The boot sequence of the instance presents panels for license agreements and the localization of the image.

实例的引导序列表示许可协议和映像位置的面板。

The first thing you will want to do is change the boot sequence of the JS20 blade server from Hard disk to CD-ROM.

首先要做的是，将 JS20 刀片服务器的引导次序由 Hard disk改为 CD-ROM。

The init process — the focus of this article — is the first process created as the kernel boot sequence is completed.

init进程——本文的重点——是内核引导过程完成时创建的第一个进程。

And you get an error I9990301 disk failure or disk reset failed then you have to switch boot sequence and make hd1 the first boot device.

可能会产生一个错误I9990301 disk failure or disk reset failed，这时必须切换引导次序，让hd 1成为第一个引导设备。

Confirm that all ports are enabled, and verify that the CD-ROM Device is listed BEFORE the Hard-Disk Drive in the Boot Sequence list.

确认所有的端口被激活，并且证实了光盘装置：硬盘驱动器的上市前的顺序列出。

The technique achieves this by allowing the latter part of the boot sequence to be run in parallel, rather than in the traditional serial fashion.

这种方法允许系统在启动服务时启动顺序中靠后的部分服务并行启动，而不是以传统的串行方式启动，以实现引导的加速。

The Linux kernel comes with lots of networking options. Because some of them need per-device configuration, the device initialization boot sequence must take care of them.

Linux内核有很多网络选项，因为它们其中的一些在每个都设备上都要配置，因此设备初始化启动顺序必须小心的应负它们。

You can change boot medium sequence by editing the server BIOS.

您可以通过编辑服务器BIOS来更改引导介质顺序。

Now that you've selected the boot method, it's time to move to the actual sequence of events that occurs after the server is powered on.

既然已经选择了启动方法，接下来了解服务器上电后实际发生的事件顺序。

The stage 1 boot loader usually loads a sequence of records called the stage 2 boot loader (or sometimes the stage 1.5 loader).

阶段 1 启动加载程序通常加载一个记录序列，该序列通常称为阶段 2 启动加载程序（有时称为阶段 1.5 加载程序）。

In fact, you can use the same sequence to install and boot any variety of operating system (production Linux distribution, Windows, or other).

实际上，您可以按照同样的顺序安装和引导任何种类的操作系统(Linux产品发行版、Windows或其他)。

If you here a sequence of beeps when you boot your machine back up, then the card may not be fully seated in the slot.

如果你在这里一个序列的蜂鸣声当你启动你的机器备份，然后在卡可能不完全固定在插槽。

If your computer doesn't boot up or at least prompt you to ask whether to boot up with CD-ROM drive, you need to change the boot up sequence setting in your BIOS.

如果您的电脑没有开机，或者至少会提示您是否启动与CD - ROM驱动器，您需要更改开机设定次序在您的BIOS。

When loading a CHD romset, the emulator will run the entire startup sequence so it will take a while to boot (early games just have a black screen) while the bios waits for the cd to spin up.

当加载CHD的rom时，模拟器会运行整个启动文件，bios等待cd加载启动，此时启动可能会花一段时间（早期的游戏会黑屏）。