The range of choice of VISO series shaft seal is wide.

VISO系列的轴封的选择范围很广。

Prevent all leakages since it has no shaft seal equipment.

防止所有漏水，因为它没有轴封设备。

Shaft seal is adapted, which can bear higher back pressure.

采用进口轴密封，能承受高背压。

The shaft seal is a part that can be damaged more easily in pump.

一般来说，釉封是泵结构中最易受损的部位。

Shaft seal skeleton oil seal, mechanical seal, packing three types.

轴封有骨架油封、机械密封、填料密封三种型式。

This paper discusses the Wet Gas Compressor shaft seal system reform.

论述了富气压缩机轴封系统改造。

Shaft seal is stuffing seal. So the price is low, and easy to maintain.

轴封为填料密封，结构简单价格便宜，且维修方便快捷。

Inspection of the pump shaft seal ring, such as wear parts should be replaced.

检查水泵轴的油封环，如磨损严重应更换新件。

This series of gear pumps are gear, shaft, pump, safety valve, shaft seal formed.

本系列齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成，齿轮油泵巩义市电话： 。

We should open and check the shaft seal. If it leaks, then replace it, if necessary.

应该拆检轴封。如果发生漏泄，有必要就换掉它。

Shaft seal: mechanical seal, according to user requirements can be used seal packing.

轴封：采用机械密封，根据用户要求也可以采用填料密封。

Shaft seal skeleton oil seal, mechanical seal, packing three type, indicate the order.

轴封有骨架油封、机械密封、填料密封三种型式，订货注明。

Most pumps used in vegetable oil plants often fail to work due to the leaking of shaft seal.

植物油厂用泵现场使用表明，大部分泵的失效是由于密封泄漏引起的。

The article further poses design thoughts of liquid charge pump which have not shaft seal contact.

进一步提出了轴封不接触泥浆灌注泵的设计思想。

Oil seal: or shaft seal, in machines, a device that prevents the passage of fluids along a rotating shaft.

油封，亦称轴封：机器中用以防止流体沿转轴泄漏的装置。

This paper presents experimental results for shaft seal assembly with three kinds of different support seats.

本文介绍了三组不同支座的轴密封部件试验结果。

Main components: two-rotor, the body, the main bearings, shaft seal, balance and energy-conditioning Pistons.

主要部件：双转子、机体、主轴承、轴封、平衡活塞及能量调节装置。

The shaft seal leakage, judgement and emergency measures of the final polycondensation reactor was introduced.

介绍了终缩聚反应器轴封泄漏的现象、判断和应急措施。

In this article, several key points in the reform of the shaft seal used in the rotary disc tower were analyzed.

本文分析了带旋转轴塔轴封改造中应注意的几个关键问题。

PW, PWF mainly by the pump cover, pump casing, impeller, shaft seal, shaft, and bracket the composition of such components.

PWF主要由泵盖、泵壳、叶轮、轴封、轴、和托架等零部件组成。

The pump consists of three sections from bottom to top: the hydraulic section, the shaft seal section and the motor section.

主泵由三个部分组成(由下而上)：水力部件，轴密封部件和电机部件。

Models shown are highly recommended where a large mechanical or rotary shaft seal is required, and low noise levels are important.

这个型号强烈的推荐大型的机械或旋转密封轴是必需的，低噪音标准很重要。

A new muddy packing is investigated by analyzing principle of packing seal and comparing with other shaft seal materials in pumps.

以新型泥状填料为研究对象，通过对密封原理的分析及新老泵类轴端密封材料性能的比较，从而得出两代密封材料的优缺点。

The general failure of podded propulsor is put forwarded. As an example, AZIPOD shaft seal arrangement and oil system are analyzed.

讲述了吊舱式推进器的易发故障，并以AZIPOD吊舱式推进器为例，对轴承和密封系统的原理和功能特性进行了分析。

Type DG pump is single casing segmental multi-stage centrifugal pump, the main parts of it are stator, rotor, bearing and shaft seal.

本型泵是单壳体节段式多级离心泵，主要由定子、转子、轴承和轴封四大部分组成。

Requirements on agitator drives; agitator speed and direction, bearing application running accuracy, dismounting space for shaft seal.

搅拌器传动装置的要求。旋转速度和旋转方向，轴承应用。

The machine imports, pumps, pump shell structure strong are the hydrostatic test, the mechanical shaft seal, stop leakage effect is good.

整机进口，泵浦结构坚固，泵壳皆经水压试验，采用机械轴封，止漏效果好。

This fact does not contact the shaft seal surface, it is the sealing principle of polymer cooled to half molten state and forming the seal.

这种密封实际上并不接触轴的表面，它的密封原理是将聚合物冷却到半熔融状态而形成自密封。