In process, the surface accuracy is affected by motion parameters such as discharging current capacity and current impulse width.

在加工过程中，加工表面精度自然受到加工参数的影响，其中包括放电电流能量、电流脉冲宽度等的影响。

The charging and discharging currents are controlled by the current flowing into IIN, and are modulated by the voltages applied to FADJ and DADJ.

充放电的电流是由流入IIN端的电流来控制的，并由加到FADJ和DADJ上的电压调制。

Low voltage charging or discharging may also cause deterioration of capacitor such as shorting and open due to sudden charging and discharging current.

即使是低电压充放电，也可能产生大的瞬间充放电电流，这可能会导致电容器性能的损害，比如说短路或开路。

The phenomenon of discharging in twice of underwater wire exploding is discovered by investigating the time characteristics of pulsed discharging current and voltage.

通过测量水中铜丝电爆炸的电流、电压波形发现水中高压放电存在着二次放电现象。

Through the experiments with quickly wire cut of electric discharge machines, this paper analyzes and studied the influence regulation of the discharging current to the surf...

通过在快走丝线切割加工机床上进行多次加工实验，本文研究分析了放电电流对线切割加工表面粗糙度的影响规律。

When it is discharging, the ions flow back and in the process cause a current to flow in an external circuit attached to the battery.

放电时，离子回流，这个过程中会在连接到电池的外部电路中产生电流。

Discharging prior to BREAK-IN mode is optional. Overcharging during the BREAK-IN mode does not harm battery as the charging current is very slow.

在使用BREAK - IN模式前先给电池放电是可以的。在BREAK - IN模式下对电池过充不会对电池造成伤害，因为充电电流非常小。

Charging speed will be improved through depolarization by first-phase intense current charging and reverse discharging method.

通过一阶段大电流充电和反向放电去极化，有效提高了充电速度。

Arc current reducing rate and arc voltage at the time of arc discharging are established for every mathematical model.

得到电弧放电瞬间每一模型下的电流变化率和电弧电压。

The experimental investigation about some hydraulics problems on cooling water discharging in current cooling technique was studied in the article.

本文针对直流冷却方式中冷却水排放相关水力学问题进行试验研究。

Based on the demand of high accurate current of battery charging and discharging in battery testing system, this paper discussed the application of Kalman filtering arithmetic in it.

针对电池检测系统中对电池充放电电流高精度的要求，论述了卡尔曼滤波算法在电池检测系统中的应用。

Thus C1 must be large enough to supply operating current to the load without discharging moue than a few millivolts.

这样C1容量必须很大才能保证C1为负荷提供运行电流而放电量不超过几毫伏。

When the battery is discharging, both ions and electrons travel spontaneously in one direction, creating a current and releasing energy.

当电池放电时，锂离子和电子将自发地做单向运动，从而产生电流释放能量。

High power batteries require high current charging and discharging abilities, low charging temperature, and good safety assurance during tactic maneuver.

特种动力电池对充放电速度、充电温度、使用安全性等都有着很高的要求。

The grounding current EMI is caused by charging and discharging of the parasitic capacitances between the circuit and ground during the switching instant devices.

地电流干扰主要是由于半导体器件开关动作产生的快速上升和下降的开关电压作用在对地电容上产生的位移电流形成的。

The aim of grounding is to provide the discharging channels for fault current and lightning current and ensure the safety of the system, the equipment and the personnel.

接地的目的是提供故障电流和雷电流泄流通道，保证系统、设备和人员安全。

The charging technique with L-C constant-current converter is adopted, and the repeated charging and discharging process of the device is controlled by voltage feedback.

研制了一种检测氧化锌避雷器阀片的重复频率充放电装置，采用L C恒流充电技术，通过电压反馈法控制充放电运行过程。

He found that, by charging a capacitor to various voltages and discharging it by short-circuiting it with the fuse, he could create a controlled amount of surge current.

他发现通过电容充电到各种电压，用保险丝短路放电，可以形成一个可控的浪涌电流。

The discharging loop includes a discharging diode connected to the current limiting charging resistance in parallel.

所述放电回路包括一放电二极管，该放电二极管并联于所述限流充电电阻两端；

The batteries had good performances of high current charging and discharging, resistance to overcharging and sealing.

此电池大电流充放性能好、耐过充能力强、密封性能好。