查询
1 词典释义:
vertical joint
时间: 2024-11-21 10:06:23

铅垂线

双语例句
  • In addition, the vertical joint and peripheral joint of the concrete face slab are also simulated.

    同时,对面板的竖缝和周边缝也可进行详细模拟。

  • The reasons for creating vertical joint crack on the reinforced concrete beam used in practical projects are analysed in this paper.

    本文针对实际工程中钢筋混凝土梁出现贯通垂直裂缝的原因进行了分析。

  • Standards from different countries adopt different failure mechanisms and do not take consideration of change of joint width in calculating shear strength in the vertical joint.

    各国规范对其强度计算采用不同的破坏机理且不考虑接缝宽度变化的影响。

  • The seepage field and stability of concrete-faced rockfill dam in Banduo Hydropower Project, when vertical joint inactivation are occurred to the face plate, are calculated by FEM method.

    以班多面板堆石坝为例,用有限元方法计算了当面板缝局部失效时各种工况下的渗流场,系统分析了大坝在面板垂直缝局部失效后的稳定渗流场的规律和特点。

  • Like previous assault ships, America can carry Harrier jump jets (pictured) and, eventually, the Marines' vertical-landing F-35B Joint Strike Fighter.

    如美国以前的攻击舰类似,可以携带鹞式飞机(如图)和海军陆战队垂直降落的F - 35 B联合攻击战斗机。

  • Sino-French joint venture to buy the vertical machining center and made more than 10 advanced air-conditioning fan and special equipment.

    购进中法合资企业的立式加工中心和国产先进的10多台空调风机专用设备。

  • A vertical stiffening rib joint is suitable for rectangular steel tube column with smaller section to H-beam connection.

    垂直加劲肋节点适用于柱截面较小的方钢管(矩形管)柱和H型钢梁节点。

  • In an enterprise middle managers are the members who engages in the activity of joint vertical correlation association and undertake the responsibility for their own department work.

    在企业中中层管理人员是指从事联结垂直性相关团体的活动,并对本部门工作承担责任的企业成员。

  • The U. S. Marine Corps F-35B short-take off vertical landing (STOVL) variant of the Joint Strike Fighter (JSF) will begin sea trials next week, the service's top aviation officer said.

    一位美国海军陆战队空军高级军官称,美军陆战队联合打击战机的F-35B垂直短距起降战机的改进型将于下周进行海上试飞。

  • The arranged pipe heater of vertical cylindrical storage oil tank often occurred damage at the joint zone between the distributor pipe and bundle.

    立式圆筒形储罐用的排管式加热器,在分配管与管束连接处经常发生损坏。

  • In order to approximate the actual vertical stiffness coefficients of the joint elements representing the shear strength of soil, formulas and iteration method are suggested.

    为确定代表土抗剪强度的节理单元竖向刚度系数,文中提出了一套相应的计算公式和试算迭代的计算方法,用来逐步逼近其真值。

  • The change of joint power of two groups of vertical jumps before and after fatigue is studied quantitatively.

    对疲劳前后的两组纵跳中关节功率的变化及其与人体疲劳的关系进行了定量分析。

  • Between slaughtering stage and retailing stage, vertical coordination takes forms of contracts, joint ventures, vertical integration and other closer means.

    新型猪肉供应链中屠宰加工企业与零售环节的垂直协作采取了合同、合资、一体化等密切协作的方式。

  • A telescoping joint at the surface in floating offshore operations that permits vessel heave (vertical motion) while maintaining a riser pipe to the seafloor.

    浮动海洋钻井作业时位于水面的伸缩节,它允许钻井船升降(垂直运动)而保持导管接触海底。

  • Avoid install the insulation joint on the vertical pipe.

    绝缘接头避免安装在立管上。

  • The vertical bearing capacity of bamboo joint pile in the engineering was researched.

    通过竹节桩在实际工程中的应用,对单桩竖向承载力进行了试验研究。

  • On the basis of experiment results processed offline, a fuzzy controller and software used in real time seam tracking of vertical fillet joint is designed.

    根据离线处理的实验结果,我们设计了一模糊控制器,开发了垂直角焊缝的实时自动跟踪软件。

  • Force transfer mechanism of the vertical stiffener joint model with only tensile beam flange is analyzed.

    本文对外肋环板节点梁翼缘受拉模型的传力机理进行了分析。

  • The vertical mortar joint cracked and the mortar in horizontal mortar joint dropped when the specimens were destroyed.

    试件破坏时大多出现竖向灰缝开裂、水平灰缝砂浆向外鼓落的情况。

  • The biomechanical parameters of 12 female weightlifters' hip and knee joint angles and angular velocity in 5 different types of vertical jump were collected and compared with their performance.

    通过采用5种不同的纵跳方式,对12名女子举重运动员髋、膝关节的角度、角速度等生物力学参数进行采集,所获数据和举重专项成绩进行相关分析。

  • On the basis of the dynamic analysis and a power-wasting theory of tenon-and-mortise work, a joint with power-wasting gap between the vertical pile and its cap is designed.

    结合整体动力分析结果,根据榫卯连接减震耗能的原理,提出一种具有耗能缝隙的直桩节点设计。