Corrugation test was conducted on a rolling vibration test rig.

再现试验用机车轮对在滚动振动试验台上进行。

This paper presents a new kind of bidirectional oil damper test rig.

介绍一种新型双向式油压减振器试验台。

The test rig and the test measurement instruments are also described.

介绍了试验装置及测量仪器。

Design of a hydraulic cylinder test rig, designed their control system.

设计了一台液压缸试验台，设计了其控制系统。

In order to test the system, a turbine test rig is designed and produced.

详细阐述了设计和制作风机发电机组实验器的过程。

Static Test Rig was used on many occasions to obtain performance data on the B-200 motor.

静态试验台是用在很多场合，以获取性能数据对B - 200汽车。

The measuring theory and demarcation method about parameters of the test rig were introduced.

介绍了双簧倒立摆试验台的测试原理，试验台参数的标定方法。

A test prototype has been designed in the paper and has been demonstrated on a engine test rig.

论文设计了原理试验样机，并在发动机试车台上进行了试验验证。

Comparative experiments of spray and packed saturators were performed with a saturator test rig.

建立了饱和器实验台，对空心饱和器和加填料饱和器进行了对比性实验。

This paper presents a simulation method of the defective lag damper fault on a helicopter rotor test rig.

提出了一种在模型直升机旋翼故障试验台上模拟减摆器失效故障方法。

The experiments on the test rig and in the running have been done about the variable geometry turbocharger.

对这种可变几何涡轮增压器进行了台架试验和跑车试验。

In this paper, the principle of load simulation and the basic structure of the brake test rig are expounded.

本文阐述了该种制动器试验台的模拟载荷原理及其基本构造。

The test rig for vehicle has been developed in order to test and evaluate endurance performance of emission.

为检测和评价汽车排放耐久性能，研制了由机器人自动驾驶的汽车排放耐久性试验台。

Experiments on the grinding wheel and the rotor test rig are carried out, which have validated the procedure.

实验表明，本文所建立的方法是有成效的，可用于转子现场动平衡。

Pressure valve test can be conducted in a dedicated test rig can also be carried out in an integrated test bed.

压力阀的测试可以在专用的试验台上进行，也可以在综合性试验台上进行。

The iteration result coincide with the road test very well prove that real road load is reproduced on test rig.

迭代结果与道路试验结果基本一致，说明在台架上可靠地复现了道路实际载荷。

The paper presents the research results of the PWM rectifier system used for the reciprocal power-fed test rig.

介绍了用于交流传动互馈试验平台的PWM整流器系统主电路的设计及参数选择。

The over-running test rig is applied to evaluate the high-speed rotating performance of the disk on the gas turbine.

本文中的超速试验台，是用来考核船舶用燃气轮机轮盘高速旋转性能的。

Huck rivet transverse vibration test rig is designed and developed to adapt mass coercive spot-check of railway truck.

为应对铁路货车铆钉质量强制抽验的要求，设计研制出哈克铆钉横向振动试验台。

The middle and high-frequency noise of the wet-style natural-ventilation cooling tower is simulated by test rig in tab.

在试验装置上进行了冷却塔噪声模拟试验，试验装置较好地模拟了火电厂湿式自然通风冷却塔的中高频噪声特性。

The design and the construction of a data acquisition and preprocessing system for a helicopter rotor test rig are described.

介绍了某直升机旋翼试验台的振动数据采集和预处理系统的设计和组成。

Metal oxide etch usually happens on the thermal hydrodynamic test rig when its equipment, pipelines and valves are made of carbon steel.

在由碳钢制造的设备、管道和阀门等部件所组成的热工水力试验台架中，金属的氧化腐蚀是一个普遍存在的问题。

An experimental verification on the turbine test rig shows that this system is effective and can be used to balance wind turbines in situ.

计量检验和风力发电机组实验器动平衡实验结果表明，该动平衡系统性能良好，实用性强。

Their separation efficiencies and flow resistances were all measured, under the same operating conditions, in a large scale cold state test rig.

在大型冷态试验台上相同的运行工况下，测试了它们的分离器效率及阻力。

The fuel assembly test rig should inspect the items mentioned above, show the values of the items and judge the inspecting results automatically.

燃料组件检查仪必须对以上项目进行自动检测，检测出各项具体数值，并且能够自动判断检验结果是否合格。

To study the spacing effect on the cooling package performance, a rear mounted wheel loader's cooling package was tested on a wind tunnel test rig.

为了研究换热器间距对冷却组性能的影响，将某轮式装载机后置冷却组放在风洞试验台上进行测试。

The full-scale three-dimensional flow centrifugal stage test conducted on an axial compressor test rignecessitates a test rig compatibility design.

在轴流压气机试验台上进行全尺寸三元流离心级的试验，需进行适台设计。

This dissertation is lucubrating test and control system of motor fatigue test rig based on computer technology and hydraulic servo control technology.

本文在计算机技术和液压伺服控制技术的基础上对多通道汽车疲劳试验台测控系统进行了深入研究和设计。

Experimental study on heat transfer and flow resistance of louver fins with 8 different structural parameters were carried out on a wind tunnel test rig.

在风洞试验台上对8种不同结构参数的百叶窗翅片进行传热和流动阻力的性能试验。

An acoustic emission (AE) test rig with signal acquisition virtual instrument system has been developed for engineering ceramics high speed deep grinding.

建立了工程陶瓷高速深磨中声发射的实验系统，自主开发了其中的声发射信号虚拟仪器采集系统。