And discussing the method compensating position error.

探讨了扫描面位置误差的补偿方法。

It focuses on the evolution of relative position error of two airplanes.

文中重点在于讨论两架飞机相对位置误差的演变。

In the end the system's position error and time error have been analyzed.

最后，对系统的位置误差与时间误差进行了分析。

A system used for position error analyzing with CMAC neural network is described.

提出一种用CMAC神经网络进行位置误差分析的系统。

CALIBRATED airspeed (CAS), Indicated airspeed (IAS) corrected for position error.

校正空速(CAS)，在修正了位置误差之后的指示空速(IAS)。

But account of action of mechanical inertia, position error will often be come of in the system.

但由于机械惯性的作用，常常会给系统带来定点误差。

The shape and position error measurement uncertainty impacts the reliability of measurement result.

零件的形位误差往往是影响整台机器工作质量的关键。

Press the "reset" key and deletes the zero position error caused by the shift of the zero point in the sensor.

“清零”键，清除传感器因零点飘移而产生的零位误差。

Scanner errors include pixel interval error, horizontal-to-vertical proportion error and starting position error.

扫描仪误差包括像素间距误差、像素间距横纵比误差及扫描起点误差等。

Two kinds of inspection methods of the position error of key slot an gear journal of crankshaft have been proposed.

提出了两种曲轴齿轮轴颈键槽位置误差的检测方法。

This paper discusses their driving, position error compensation and use value so as to offer a reference for study.

本文将论述其传动、位差补偿及应用价值，供研究参考。

To reduce influence of mounting position error, sensor static calibration and coordinate transform are implemented.

提出了通过传感器静态标定和坐标变换来减少安装误差影响的方法。

The result shows that disturbing torques are increased with both the diameter error of orifices and their position error;

结果表明，节流孔尺寸误差越大、位置偏移误差越大，引起的干扰力矩越大；

The second part is to investigate the utilization for outside information of vehicle to estimate the impact position error.

第二部份研究利用外部信息估计落点偏差。

This paper presents a method of robot position error compensation and introduces a high precision positioning system of robot.

本文提出了一种机器人高精度定位补偿系统，介绍了一种位姿误差补偿方法。

Analyses show that a measurement of 5 points altitude in the free flight path, the impact position error may be estimated probably.

分析表明，在自由飞行段5点测高可以估出落点偏差。

The mathematical model between position error and north seeking error is gotten through error theory and partial derivative principle.

运用误差理论和偏导数原理，推导出转位误差与寻北误差二者之间的关系模型。

In this paper, author studies the position error-compensating control problem of cutting process by using the classical control theory.

本文作者运用经典控制论对切削过程的位置误差补偿控制进行了研究。

The paper introduces the position design of two-hole-one-side clamping apparatus, position error calculation and its features through examples.

通过实例介绍了两孔一面定位方式夹具的定位设计，定位误差计算及特点。

Position prediction algorithm is introduced to compensate the position error in the sampling time, or the extra torque ripple would be produced.

针对采样周斯内的位置误差会引起电机额外的转矩波动，本文引入了位置预测算法。

The poison error along disk tangential direction decreases the DPD signal amplitude, and the factor is 1.52T when position error is less than 25%.

计算结果表明：沿盘片切向的位置误差使DPD的幅值变小，在25%的范围内DPD的幅值随切向位置误差的变化系数为1.52T；

The star point of the dynamic star simulator's showing grid is measured, and the position error correction factor of each star point is calculated.

利用经纬仪对动态星模拟器显示的网格上的星点进行测量，计算了各星点的位置误差及修正系数。

In the perpendicular direction to the rotation axis of the petal, the repeat position error is most sensitive to the position error of the locking force.

在对接面内与旁瓣转轴方向相垂直的方向上，重复定位误差对锁紧力位置误差最为敏感。

This paper discusses and analyzes the accuracy problem of linear-resection points. At the same time, the property graph of point position error is given.

讨论与分析了测边后方交会点的精度问题，同时给出了点位误差特性曲线图。

The results show that using the method of GPS, through level accelerate flight and level decelerate flight, we can get the shock and position error curves fully.

结果表明，采用GPS法，通过平飞加、减速飞行，可以获得完整的气动激波修正量曲线。

Through the analysis on every procedure of surveying 1:500 topographic map with the method of transit mapping, the position error of 1:500 topographic map is got.

通过对经纬仪测绘法1：50 0地形测图过程中各个工序的分析，得出了1：50 0地形图上的点位中误差。

The paper has proved theoretically and verified statistically by sampling that the distribution of the position error in arbitrary direction is Rayleigh Distribution.

本文从理论上证明并抽样统计验证了任意方向位置度误差服从瑞利分布；

Simulation results show that this integrated system can get navigation attitude position with high precision, also the position error and velocity error are decreased.

仿真结果表明：本文提出的组合导航系统能够给出载体的高精度姿态信息，位置误差和速度误差也较小。

The measurement equation for multi position error separation technique is put forward, and the equation is universal for all the current multi step and multi point methods.

提出了多位法误差分离技术读数方程，可统一现行的多步法和多点法。